Back to Blog
Tips & Care 2026-11-16 Newtype: Gundam Model Kits / Gunpla / Paint / Tools 0 views

GD-64 MG Cherudim Gundam Decals: Placement Tips for Clean Results

GD-64 MG Cherudim Gundam Decals: Placement Tips for Clean Results

Get clean results with GD-64 MG Cherudim Gundam decals. Learn practical placement, setting, and care tips for these 1/100 waterslide decals.

Why decal placement makes or breaks a Cherudim build

Adding decals to your MG Cherudim is one of the quickest ways to sharpen its look, but placement and care decide whether the result looks factory-fresh or fussy. The GD-64 MG Cherudim Gundam Decals from Bandai are 1/100-scale waterslide decals designed to enhance the visuals of any model kit. This guide walks through practical steps for placing them cleanly and keeping them intact.

What the GD-64 decal set gives you

  • GD-64 MG Cherudim Gundam Decals: Gundam Decal- Cherudim 1/100 scale Gundam Water decals by Bandai open up detail options to any build. These are waterslide decals in 1/100 scale, so they suit MG Cherudim and other 1/100 kits. Knowing the type helps you choose the right application method.
    GD-64 MG Cherudim Gundam Decals
    GD-64 MG Cherudim Gundam Decals
  • GD-64 MG Cherudim Gundam Decals: Gundam decals are designed to enhance the visuals of any model kit. The set is meant to add detail rather than change the kit's structure, so you can focus on placement and clean adhesion.

A practical sequence for placing Cherudim waterslide decals

Waterslide decals need a little patience. Follow these steps to help them sit flat and stay put.

  1. Plan the layout before you wet anything: Test-fit decals on the dry model to decide where each marking looks best. Because these are 1/100 scale, check that the size suits the panel you're decorating.
  2. Prepare the surface: Make sure the plastic is clean and dry. A smooth, dust-free surface helps the decal adhere evenly.
  3. Slide the decal into place: Soak the decal briefly in water, then slide it off the backing paper onto the model. Use a soft brush or your finger to position it without stretching.
  4. Blot and smooth: Gently press out trapped water and air bubbles with a soft cloth or cotton swab, working from the center outward.
  5. Let it set completely: Allow the decal to dry undisturbed. Avoid touching or handling the area until it's fully set.

Placement tips for a cleaner look

  • Use reference images: Bandai's official photos or the kit's manual can suggest typical decal locations. These decals are designed to enhance any build, so you can also follow your own taste.
  • Keep markings symmetrical where it matters: For a balanced look, mirror decals on opposite sides of the body. Measure or eyeball carefully before committing.
  • Avoid curved areas that fight the decal: Waterslide decals conform best to gentle curves. On sharp bends, make small relief cuts with a hobby knife if needed, but test on a spare decal first.
  • Don't overcrowd: A few well-placed decals often look better than covering every panel. Let the Cherudim's design breathe.

Setting solutions and topcoats: what to consider

Decal setting solutions can help soften the decal so it hugs panel lines and curves, but they're not mandatory. If you use one, test it on a spare decal first to make sure it doesn't distort the print. A clear topcoat over the finished model can protect the decals from wear and even out the sheen, but check that your chosen topcoat is compatible with waterslide decals. The supplied information for this set doesn't include specific setting or topcoat instructions, so treat any product you add as your own choice and follow its label.

Care tips to keep your Cherudim decals intact

  • Handle the model by its base or large parts: Fingers can lift decal edges. Support the model from sturdy areas when posing or moving it.
  • Dust gently: Use a soft brush or a puff of air rather than a cloth that could catch an edge.
  • Keep it out of direct sunlight and heat: Prolonged exposure can fade or weaken decals over time. A display case or shelf away from windows helps.
  • Repair lifting edges early: If a corner starts to lift, a tiny dab of water or a decal adhesive (if you use one) can re-seat it before it peels further.

What the supplied information doesn't cover

The product record for GD-64 MG Cherudim Gundam Decals doesn't list a specific age range, drying times, or compatibility with every topcoat. It also doesn't include step-by-step instructions from Bandai. Use the general waterslide guidance above as a starting point, and check the decal sheet or Bandai's official channels for any additional details. If you're new to waterslide decals, practice on a spare or inconspicuous area first.

Related Articles

Customer Service
Home
Products
Cart
Profile