Delpi Decal MG シナンジュ・スタイン Ver.Ka：貼り方ガイド
By Newtype: Gundam Model Kits / Gunpla / Paint / Tools | Published: 2026-10-31
Category: ハウツーガイド
Delpi Decal MG Sinanju Stein Ver.Kaの水転写デカールを、説明書に沿った配置手順、表面の下準備、セッティング液を使ってきれいに貼りましょう。
Quick answer
Apply Delpi Decal MG Sinanju Stein Ver.Ka decals by following the original kit manual for placement, working one decal at a time with a setting solution, and sealing only after everything is fully dry.
Why the kit manual is your placement map
Delpi Decal designed this set for use with the original MG 1/100 Sinanju Stein Ver.Ka manual, so the manual is not just a suggestion—it is the reference for accurate placement. Skipping it leads to decals that look busy but wrong, especially on the shoulders and skirt armor where Ver.Ka markings are dense.
Keep the manual open to the decal diagram page and cross off each decal as you apply it. This prevents double-application and missed spots.
Surface prep matters more than decal brand
Waterslide decals bond to a clean, glossy surface. If you have painted or topcoated, ensure the surface is fully cured and free of dust. On bare plastic, a quick wipe with a lint-free cloth and mild soapy water (then dry) removes mold release agents that cause silvering.
A glossy clear coat before decaling gives the decal a smooth bed to settle into; a flat coat before decaling can trap air under the film.
When to use setting solutions—and when to skip them
Setting solutions help decals conform to curves and panel lines, but too much can soften the film and cause tearing. Use a small amount of setting solution on the model surface before sliding the decal, and avoid flooding the area.
If you are new to waterslides, practice on a spare part or an inconspicuous area first. Delpi Decal sets are known for quality, but technique still determines the final look.
Step-by-step decal application
- Prepare the surface: Clean the model with a lint-free cloth and mild soapy water, then dry completely. If you have painted or topcoated, ensure it is fully cured. A glossy, clean surface prevents silvering; avoid flat coats before decaling.
- Set up your workspace: Open the original kit manual to the decal diagram. Fill a shallow dish with lukewarm water and have tweezers, a cotton swab, and a soft cloth ready. Cross off each decal on the manual as you apply it to avoid missing or doubling up.
- Cut and soak the decal: Cut out the decal with a small border of film, then soak it in water for 10–20 seconds until it slides easily on its backing paper. Do not oversoak; if the decal floats off the paper, it may fold or tear.
- Apply setting solution (optional): If using a setting solution, brush a thin layer onto the model surface where the decal will go. Avoid pooling. Too much solution can make the decal overly soft and prone to tearing.
- Slide and position the decal: Slide the decal off the backing paper onto the model using tweezers or a wet finger. Position it according to the manual, then gently blot excess water with a cotton swab. Work one decal at a time; repositioning becomes difficult as the decal sets.
- Blot and dry: Press the decal down with a dry cotton swab, working from the center outward to remove air bubbles and excess water. Let it dry completely for several hours. Do not touch or topcoat until the decal is fully dry; otherwise it may shift or wrinkle.
- Seal the decals: After all decals are dry, apply a clear coat (gloss or flat) to protect them and unify the finish. Sealing is essential for durability and to blend the decal film edges.
Product facts
- Delpi Decal MG Sinanju Stein Ver.Ka: This decal set is designed for use with the original MG 1/100 Sinanju Stein Ver.Ka model kit manual. Following the manual ensures correct placement and a clean, detailed finish without guesswork.
Delpi Decal MG Sinanju Stein Ver.Ka
