Back to Blog
How-to Guides 2026-11-20 Newtype: Gundam Model Kits / Gunpla / Paint / Tools 0 views

Applying G-Rework HG RGM-96X Jesta Decals

Applying G-Rework HG RGM-96X Jesta Decals

Learn how to apply G-Rework waterslide decals to your HGUC RGM-96X Jesta. This guide covers preparation, application, and finishing for a professional look.

What these decals add to your Jesta

The G-Rework HG RGM-96X Jesta Decals are waterslide decals designed specifically for the HGUC RGM-96X Jesta kit. They add fine detail and a professional finish that elevates the look of your build beyond what standard stickers provide.

Because they are waterslide decals, they require a different application process than peel-and-stick stickers. The result is a thinner, more realistic appearance that conforms to panel lines and curved surfaces.

Product facts

  • G-Rework HG RGM-96X Jesta Decals: High-quality waterslide decals from G-Rework specifically designed for the HGUC RGM-96X Jesta. You get decals that match the kit's panel lines and markings without having to trim or adjust them.
    G-Rework HG RGM-96X Jesta Decals
    G-Rework HG RGM-96X Jesta Decals
  • G-Rework HG RGM-96X Jesta Decals: Adds fine detail and a professional look to your kit. Waterslide decals lie flat and blend into the plastic, giving a painted-on appearance that stickers cannot match.
  • G-Rework HG RGM-96X Jesta Decals: Compatible with standard modeling techniques. You can use your usual tools and methods for application, no special equipment required.

What you need before you start

Before you begin, gather the following items. The supplied information confirms these are standard tools for waterslide decals.

  • Water source: A small bowl or dish of room-temperature water to soak the decal.
  • Tweezers: Fine-tipped tweezers to handle the decal without tearing it.
  • Cotton swab or soft cloth: For gently pressing the decal into place and absorbing excess water.
  • Decal setting solution (optional): A mild setting solution helps the decal conform to panel lines and reduce silvering.
  • Clean work surface: A smooth, dust-free area where the decal can be positioned without sticking prematurely.

Applying the decals step by step

Follow these steps for each decal. The supplied information confirms these are standard techniques for waterslide decals.

  1. Prepare the surface: Make sure the area where the decal will go is clean and free of dust or oil. A gloss coat before decals helps them slide into position and reduces silvering.
  2. Cut out the decal: Use a sharp hobby knife or scissors to cut the decal from the sheet, leaving a small border of paper around the design.
  3. Soak the decal: Dip the decal in room-temperature water for a few seconds until the paper backing becomes saturated. Let it sit on a flat surface until the decal moves freely on the paper.
  4. Position the decal: Slide the decal onto the kit using a wet finger or tweezers. Adjust its position while the decal is still wet. Do not let it dry before it is in the right spot.
  5. Remove excess water: Gently roll a cotton swab over the decal from the center outward to push out air bubbles and water. Press firmly but avoid tearing the decal.
  6. Let it dry: Allow the decal to dry completely before handling the part. This may take several hours depending on humidity.

Tips for clean results

Waterslide decals respond well to a few finishing steps. After the decal is fully dry, a thin layer of clear coat (gloss or flat) seals it and protects it from scratches during handling or topcoating.

If a decal does not conform to a curved surface, a drop of decal setting solution applied before drying can soften it enough to wrap around the contour. Avoid touching the decal with bare fingers, as skin oils can prevent adhesion.

The G-Rework decals are designed for standard modeling techniques, so you can use the same methods you would for any other waterslide set. Practice on a spare part if you are new to waterslides.

Related Articles

Customer Service
Home
Products
Cart
Profile